Metra Electronics Automobile Accessories 99 3106 User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-3106  
APPLICATIONS  
SATURN  
2003-05 Ion / 2000-05 LS  
2000-02 SL / 2002-05 Vue  
99-3106  
KIT FEATURES  
• Double DIN Head Unit Provisions with Pocket  
• ISO DIN Head Unit Provisions with Pocket  
KIT COMPONENTS  
A) Radio Housing • B) Pocket • C) Radio Housing Brackets • D) (6) Phillips Screws  
B
C
D
A
TOOLS REQUIRED:  
Socket Wrench • Flat Blade Screwdriver • Phillips Screwdriver • Cutting Tool  
1-800-221-0932  
Rev. 06-14-07 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-3106  
 
99-3106  
2003-2005 SATURN ION  
Disconnect the negative battery  
terminal to prevent an accidental short  
circuit.  
1
2
3
Unclip and remove the trim panel  
surrounding the radio. (Figure A)  
Remove (2) 9/32” screws from radio to  
remove. (Figure A)  
A
2000-2005 SATURN LS  
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
1
B
Unclip and remove the trim panel  
surrounding the radio. (Figure B)  
2
3
Remove (2) 9/32” screws from radio  
to remove. (Figure B)  
1
 
99-3106  
2000-2002 SATURN SL  
A
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
1
2
3
4
Remove (4) Phillips from panel below  
steering column and unclip and  
remove. (Figure A)  
B
Remove (4) Phillips screws from the  
steering column trim panel and  
remove. (Figure B)  
Remove (2) screws from the end  
cap/vent on the left side of the  
steering column then unclip and  
remove. (Figure C)  
Unclip and remove the entire dash  
panel surrounding the radio, instru-  
ment cluster and a/c controls.  
(Figure D)  
5
6
C
Remove (2) 9/32” screws securing  
the head unit to remove. (Figure D)  
D
2
 
99-3106  
2002-2005 SATURN VUE  
A
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
1
2
Unsnap and remove shifter trim  
panel. (Figure A)  
Remove (4) 9/32” screws from the  
dash pocket and remove. (Figure A)  
3
4
Unsnap and remove panel surround-  
ing radio and a/c controls.(Figure A)  
Remove (2) 9/32” screws from radio  
5
to remove. (Figure A)  
3
 
99-3106  
ISO DIN HEAD UNIT PROVISIONS  
A
Slide the radio housing brackets  
onto the radio housing. (Figure A)  
1
2
Snap the pocket onto the back of the  
radio housing, align the holes in the  
pocket with the holes in the radio  
housing brackets and mount with  
the (6) Phillips screws supplied.  
(Figure B)  
B
Align the holes in the radio housing  
brackets with the holes in the ISO-  
DIN head unit and secure the brack-  
ets to the head unit with the screws  
included with the unit. (Figure C)  
3
C
4
 
99-3106  
DOUBLE DIN HEAD UNIT PROVISION  
A
Cut and remove the center bar on  
the radio housing (A), the protruding  
bracket tabs (B), the bracket sockets  
(C), and the locating pins on the  
back of the radio housing (D).  
(Figure A)  
1
Slide the radio housing brackets  
onto the sides of the radio housing.  
(Figure A)  
2
3
B
Align the holes in the radio housing  
brackets with the holes in the DDIN  
head unit and secure the brackets to  
the head unit with the screws  
included with the unit. (Figure B)  
5
 
INST99-3106  
A
B
A)  
B)  
C)  
D)  
Strip wire ends back 1/2"  
Twist ends together  
Solder  
Tape  
C
D
Locate the factory wiring harness in the  
dash. Metra recommends using the  
proper mating adapter and making the  
connections as shown. (Isolate and indi-  
vidually tape off the ends of any unused  
wires to prevent electrical short circuit)  
1
Re-connect the negative battery terminal  
and test the unit for proper operation.  
2
Reassemble radio and dash assemblies in  
reverse order of disassembly.  
3
6
 

Kunz Lawn Mower MR55B User Manual
Kustom Stereo Amplifier KBA115C KBA210C User Manual
LG Electronics Car Stereo System GD900 User Manual
LG Electronics CRT Television 22LY340C User Manual
Logitech Mouse M525 User Manual
LST Smoke Alarm 2100RFT AS User Manual
Makita Grinder GA7050 User Manual
Makita Pole Saw 4604D User Manual
Manitowoc Ice Cooktop GI SH BA 3500FH User Manual
Melissa Blender 646 067 User Manual